Car Key Button Repair
A broken car key is a hassle. It is possible to contact a 24-hour locksmith Service for assistance or to purchase a new remote.
You may be able save money by repairing your old key fob rather than replacing it. This is especially true when an old switch or damaged contacts are at the root of the issue.
Battery
If the buttons on your key fob do not respond when you pressing them, this could indicate that the battery is dead or is close to the end of life. Fortunately replacing the battery is a simple task that you can complete on your own instead of hiring a locksmith or dealer to take care of it.
Locate the battery compartment first. The battery compartment is usually located on the back of the key fob and can be hidden behind a cover that slides out or an open button that opens the access point. Once the compartment has been exposed then look for the small button-cell battery. It is usually shaped like a small coin and identified with a plus and the minus symbol. Remove car key fob repair and put a brand new one in its place, ensuring that the plus and minus signs are correctly aligned.
Close the compartment and snap the two parts of your key fob. Before closing the door ensure that you align and snap the parts into place. To ensure that the buttons work properly, press any of them.
If your remote keyfob isn't working after replacing the battery, there may be other issues that require a different type of repair. Damage to the physical structure caused by dropping the fob in a puddle for instance may cause it to stop functioning altogether. It could also be experiencing an internal electrical failure or it may require to be deprogrammed by a locksmith or locksmith. Find out if the issue is with your key fob using these other common automotive troubleshooting methods.
Switches
There are many kinds of switches that are used in the car key fob, dependent on the year and make. The older model keys usually have a separate chip which is visible in the case, whereas modern keys are more sophisticated and function by sending signals to the car. Regardless of the type, the buttons on the key may get worn down or damaged with normal use. This causes them to become difficult to press or even unresponsive. If you attempt to force the button to function it could cause further damage, and could even prevent the key from starting your vehicle in the future.
If your key doesn't seem to be working, first try changing the battery. If that doesn't work, you may need to clean your key fob and re-adjust the switches. These tiny electronic switches are more susceptible than larger parts of the key to break because they are constantly jostled.
The switches have a rubbery feel and are coated with a film that conducts electricity. The film may be worn away over time. Fortunately, they're small and inexpensive to replace. They're soldered on the circuit board, therefore it is important to remove the old ones without damaging other components. You can then solder new ones in and reassemble your fob.
Don't use your car key fob for more than an hour at a stretch and avoid leaving it visible. Also, make sure you find a secure location to keep your key in when you aren't using it.
If the problem persists after you've cleaned the key fob or battery, and tried to clean it, then you may need to consult an expert locksmith. A professional can check the frequency of your key to determine whether it's still able communicate with your vehicle, open and replace micro switches, swap cases, and more.
Outer Case
Key fobs spend much of its time bouncing around, and when the buttons aren't allowed to move upwards and downwards within the case, they could become stuck or broken. If replacing the battery or cleaning with a cotton swab and some rubbing alcohol don't resolve the issue, taking off the case and inspecting could be required. If the contacts that the buttons touch are not a good fit, or if they are worn, adjusting them may be the only solution.
Certain keys have rubber buttons which can wear away over time. The rubber stretches and nails pierce it and the buttons can become difficult to press. This could cause the key to fail, and in this case it is time for an entirely new case or buttons. This repair involves disassembling your remote, locating the button switches on the board, heating the solder, and carefully taking them off. The circuit board is then soldered with new buttons. The case can then be reassembled and the horse shoe key blade piece is attached. The new buttons must be tightly fitted into the case in order to prevent them falling out.
Inner Case
Since your key fob is prone to be tossed around and could occasionally be pressed by accident, the buttons inside can become stuck or broken over time. Utilizing metal tape and a hole punch, you can often quickly solve this issue when your car is not at home and the key fob doesn't work and allows you to open the doors, but not start the engine. This quick fix could allow you to safely return to your vehicle to complete your trip.